little discrepancy between the code and the default PRT pivot points

• 10/17/2023 at 7:20 AM #222541
  Inertia

  PP Weekly

  // POINT PIVOT HEBDOMADAIRE IF dayofweek < dayofweek[1] THEN weekhigh = prevweekhigh weeklow = prevweeklow weekclose = prevweekclose prevweekhigh = high prevweeklow = low ENDIF prevweekhigh = max(prevweekhigh, high) prevweeklow = min(prevweeklow, low) prevweekclose = close PPWeek = (weekhigh + weeklow + weekclose) / 3 Res3 = Res1 + (weekhigh - weeklow) Res2 = PPWeek + weekhigh - weeklow Res1 = (2 * PPWeek) - weeklow Sup1 = (2 * PPWeek) - weekhigh Sup2 = PPWeek - (weekhigh - weeklow) Sup3 = Sup1 - (weekhigh - weeklow) Return Res1 AS "Res1" coloured("green"), Res2 AS "Res2" coloured("green"), Res3 AS "Res3" coloured("green"), PPWeek AS "Pivot" coloured("black"), Sup1 AS "Sup1" coloured("red"), Sup2 AS "Sup2" coloured("red"), Sup3 AS "Sup3" coloured("red"), PPWeek COLOURED(50,50,220) AS"Pivot Week"

  1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

  // POINT PIVOT HEBDOMADAIRE IF dayofweek < dayofweek[1] THEN weekhigh = prevweekhigh weeklow = prevweeklow weekclose = prevweekclose prevweekhigh = high prevweeklow = low ENDIF prevweekhigh = max(prevweekhigh, high) prevweeklow = min(prevweeklow, low) prevweekclose = close PPWeek = (weekhigh + weeklow + weekclose) / 3      Res3 = Res1 + (weekhigh - weeklow) Res2 = PPWeek + weekhigh - weeklow Res1 = (2 * PPWeek) - weeklow Sup1 = (2 * PPWeek) - weekhigh Sup2 = PPWeek - (weekhigh - weeklow) Sup3 = Sup1 - (weekhigh - weeklow)   Return Res1        AS "Res1"      coloured("green"), Res2        AS "Res2"      coloured("green"), Res3        AS "Res3"      coloured("green"), PPWeek        AS "Pivot"      coloured("black"), Sup1        AS "Sup1"      coloured("red"), Sup2        AS "Sup2"      coloured("red"), Sup3        AS "Sup3"      coloured("red"), PPWeek COLOURED(50,50,220) AS"Pivot Week"

  Hi, there is couple of gap pts between the code attached end the PRT point pivots.

  Any idea why?

  Thank you.

  

  Inertia

  Participant

  Topics: 40

  Replies: 223

  Been thanked: 52 times
  10/17/2023 at 7:21 AM #222542
  Inertia

  here is a link >

  

  Inertia

  Participant

  Topics: 40

  Replies: 223

  Been thanked: 52 times
  10/19/2023 at 6:54 PM #222666
  Inertia

  Hello all,

  Question about multiple triggers versus one single line to trigger a trade.

  Attached are two pictures with both the same trigger: Point Pivots mS1M (33635)

  One works fine, not the other (with more lines in it).

  Any idea why please?

  Thank you

  Damien

   

   

  

  Inertia

  Participant

  Topics: 40

  Replies: 223

  Been thanked: 52 times
• Author
  Posts